一、適用
　　鞋材網布，萊卡布,牛仔布(涂層布，壓光布除外)、尼龍布、TPU、PU皮革，及一些高彈性面料等。
二、性能指標
◇外觀及組成：白（透明）粘稠狀體，聚氨酯聚合物
◇布氏粘度：140000~160000CPS
◇PH值：7.0-8.0
◇離子類型：陰離子
◇固體含量：65%±1
三、特性
PU0316鞋材立體水性墨白（常溫耐折12-15萬，低溫耐折12-15萬，雙組份）：立體感強，白度好，觸邊性好，高附著力，高亮光，表面光滑，干爽，耐高溫水洗。優越的低溫耐折型

PU0316鞋材立體水性墨透（常溫耐折12-15萬，低溫耐折12-15萬，雙組份）：立體感強，高透明，觸邊性好，高附著力，高亮光，表面光滑，干爽，耐高溫水洗。優越的低溫耐折型
四、操作應用
◇本產品一般使用80目120目網布，根據圖案的不同絲網一定要繃緊，這一點相當關鍵。
◇為了保證印制效果，一般不要制作太厚網版，根據厚度不同需要印5—8次，在使用厚網版印刷時印完第一次需待底層干透后再進行第二次印刷，一般印刷3—5次就能達到2-3毫米以上的高度。
◇本產品不易塞網，過稠時可加入適當水漿攪拌均勻進行稀釋。
◇在自然風干48小時后，再過溫150度8-15秒，過溫時盡量將面料過反面。
◇使用時加入1%-2%交聯劑。（加好助劑的漿料要在3~6小時內用完）。
五、注意事項
◇自然干燥時間與氣溫和空氣濕度有關。
◇調色可根據客戶需要顏色的深淺來調入色種的分量，顏色調入太多容易引起掉色現象，色種最好控制在5%之內。
◇如印容易掉色的深色布，需要測試顏色是否會升華到膠漿表面上，以減少不必要的損失。
◇使用本透明產品印花，要稍加白膠漿摻和進行調色印花有利于在紡織品面料上印花著色度飽和，更好發揮透明漿的應用效果。
◇由于印花面料的多樣化，和一些外在的不確定因素做大貨之前先小樣實驗確定以后方可批量生產。未確定情況使用或操作不當引起的質量問題本公司概不負責。

Other detailed information

1. Substrates

   Shoe material mesh,Lycra,denim(besides coated fabric,press gloss cloth),Nylon,TPU,PU leather and some good elastic fabric.

2. Performance and indicators

   Appearance and composition: white (clear)viscous body, polyester

   Brinell viscosity:140000-160000CPS

   PH value:7.0-8.0

   Ionic:anion

   Solid content:65%±1

3. Features

4. PU0316 shoe material stereo waterbased ink white（normal temperature folding 12-15萬,low temperature folding 12-15萬，two-component）：high stereoscopic,good whiteness,good edge,high adhesion,high glossiness,sooth surface,dry,resistance to hight temperature washing,.excellent low temoerature folding.

   PU0316 shoe material stereo waterbased ink clear（normal temperature folding 12-15萬,low temperature folding 12-15萬，two-component）：high stereoscopic,high transparency,good edge,high adhesion,high glossiness,sooth surface,dry,resistance to high temperature washing.excellent low temperature folding.

   
   

   
   

5. Operation application

   This product uses 80-120mesh screen as usual. The crux is that according to different shape,the mesh screen must tighten.

   In order to guarantee the printing effect,should not manufacture thick mesh screen. According to different thickness, it needs to print 6-8times.When using thick mesh screen print, what we should notice that it must be dry enough and then print in second time.Printing 3-5times can reach the height of2-3mm.

   This product is not easy to plug mesh,you could add suitable water slurry and stir to dilute when it too thick.

   After air dry naturally for 48 hours,and then over-temperature for 8-15seconds at 150℃.When over-temperature,it better to put fabric in opposite side.

   You should add 1%-2%crosslinker when using the product.(The paste with auxiliaries ,you should run out within 3-6hours.)

6. Notes

   The time of drying is related to humidity of the air.

   When adjusting the color,the amount of pigment you should add according to the customer’s needs.If add too much color, it will lead to come off, the amount of pigment it better to add within 5%.

   If print on dark fabric which is easy to come off, it better to make a test that color whether sublimate on the surface of paste, in order to reduce unnecessary financial losses.

   Using this transparent product to print,add some white paste to print ,it could makes the textile surface looks more saturated and make the clear paste reach the best application effect.

   Due to variety of printing fabrics and some uncertain factors outside , you should better make a test before in a batch production. Our company is not responsible for quality problem which caused under uncertain condition or operate incorrectly.